Characteristics & Operation of Enhancement Type MOSFETs 

Enhancement Type MOSFETs 

In this type of MOSFET, channel is formed after applying biasing hence it is named as enhancement type. This MOSFET is smaller in size, economical and provides better performance than depletion MOSFET.

Figures 1(a) and (b) depict the cross-sectional view and circuit symbols of n-channel enhancement type MOSFET, respectively.

The broken line in the symbol indicates the absence of a channel.

Here the Al plate is replaced by polycrystalline Si material. The source and drain are kept apart as there is no channel existing in between source and drain region.

In this MOSFET, the channel is created by applying proper V_GS. When positive gate to source voltage is applied, electron starts accumulating under gate; hence channel is formed.

Since p-substrate is converted to n-channel due to accumulation of electrons under the gate; it is also called inversion layer. The channel is also called induced channel.

The MOSFET acts as a capacitor which is formed because of positive metal plate (polycrystalline silicon), negative inversion layer and a SiO₂ dielectric sandwiched between them, when a positive drain to source voltage is applied. A high intensity electric field is produced and electrons start moving from source to drain.

Operation of Enhancement Type n-Channel MOSFET

Figure 2 shows the construction and working of n-channel enhancement MOSFET.

1. If drain terminal is kept floating, no current will be passing through the channel, that is, I_D = 0. Thus the MOSFET does not conduct when V_GS = 0 because there is no channel available for flow of drain current. The MOSFET is now working as a parallel plate capacitor.

For the MOS capacitor, the oxide capacitance (C_ox) per unit cross sectional area is given by

Where ε_ox is permittivity in F/m and given by ε_ox = ε₀ ε_r

For SiO₂, ε₀ is absolute permittivity of for free space = 8.854 × 10⁻¹² and ε_r = relative permittivity = 3.9.

Therefore, ε₀ ε_r = 8.854 × 3.9 × 10⁻¹² = 3.45 × 10⁻¹¹ F/m

Gate capacitance is given by C_gate = C_oxWL Farad

Where L is the length of the gate plate or channel and W is the width of the gate plate.

W/L > 1.

W/L Ratio is called aspect ratio per feature size. 

2. The drain current can pass through the MOSFET only when V_DS is applied. The circuit for n-channel enhancement type MOSFET when V_DS is applied is shown in Fig. 3(a).

When V_DS is kept at zero, the diode is unbiased and in the absence of depletion layer the channel will remain flat. When V_DS is large, the diode is reverse biased at the drain, depletion layer will penetrate more into substrate tapering the channel and due to high electric field current becomes constant. This is depicted in Fig. 3(b).

When V_DS is of large value, a p-n junction is formed at drain and gets reverse biased and depletion layer is increased as shown in Fig. 4.

3. The discontinuity of the channel can be avoided by connecting substrate voltage V_SB or body voltage.

When V_DS is increasing, the channel length decreases and this whole process where the length of the channel can be altered by varying V_DS is called the channel length modulation (CLM). CLM effect occurs only in enhancement MOSFET.

Due to CLM, EMOSFETs cannot be operated with self-biased arrangement or potential divider bias circuit.

Some important points related to n-channel enhancement type MOSFET are: 

• Channel potential increases from source to drain.  
• Inversion charges decrease from source to drain.  
• When V_GS = 0, I_D = 0. 

The transfer and drain characteristics of n-channel enhancement MOSFET are shown in Fig. 5(a) and (b).

From the transfer characteristic curve, we have for V_th as the threshold voltage:   

• If V_GS < V_th MOSFET is in OFF state 
• When V_GS > V_th MOSFET is in ON state

From the drain characteristic curves, we have: 

• When V_DS = V_GS — V_th or V_DS > V_GS — V_th, the MOSFET is operating in the saturation region. 
• When V_DS < V_GS — V_th, the MOSFET operates in linear region V_DS < V_DS(sat) 
• Equation for drain current in saturation region is 

Where V_GS >> V_th

Some important relations for n-channel enhancement type MOSFET 

When V_GS < V_th; I_D = 0; cut-off region. 

When V_DS < V_GS — V_th; I_D = linear current; linear/ triode region. Drain current is given by

When V_DS ≥ V_GS — V_th; I_D = saturation current;  saturation region. Drain current is given by

Operation of Enhancement Type p-Channel MOSFET

The p-channel enhancement type MOSFET is similar in construction and operation to n-channel enhancement type MOSFET.

Figures 6(a) and (b) show the cross-sectional view and the circuit symbols for p-channel E-MOSFET.

Some important relations for p-channel E-MOSFETs 

When V_GS > V_T ; I_D = 0; cut-off region 

When V_DS ≥ V_GS — V_T ; I_D is linear; active/linear/triode region. Drain current is given by

When V_DS < V_GS — V_th; I_D is constant; saturation region. The drain current is given by

The characteristics of depletion and enhancement MOSFETs are compared in following Table.

Threshold Voltage

Threshold voltage (V_th) is the minimum gate to source voltage at which conduction starts in a MOSFET. It can be graphically obtained from the transfer characteristics of MOSFET and appears only in enhancement type MOSFETs as shown in Fig. 7.

The voltage at which the MOSFET enters into ON state: 

• V_th is positive for n-channel MOSFET   
• V_th is negative for p-channel MOSFET 

The value of V_th lies in the range 0.5 V to 3 V (typical value 1V). V_th must be small for better performance of MOSFET. The advantages of its small value are listed as follows:  

• Enables the device to operate with smaller supply  voltages.  
• Increases the compatibility of device.   
• Reduces switching time of devices so that they  become faster in operation.

The threshold voltage for n-channel E-MOSFET is given by

Where:

γ is fabrication process parameter.

φ_F is physical parameter of Fermi voltage.

V_SB is substrate voltage or body voltage.

N_A is accepter concentration or doping concentration of p-type substrate in n-channel MOSFET.

V_th(0) is threshold voltage of MOSFET when substrate voltage is kept zero (V_SB = 0)

From the equation for threshold voltage, we have V_th α V_SB

Normally body and the source are tied to the ground. If body voltage (V_B) drops below the source voltage, V_SB increases. If V_B becomes more negative, more holes are attracted towards body connection leaving a larger negative charge behind.

Hence, the depletion region becomes wider. Thus, V_th is the function of total change in the depletion region.

As V_B decreases, depletion region increases and threshold voltage increases. This is called body effect or back gate effect or substrate bias effect and is depicted in Fig. 8.

The threshold voltage of MOSFET can be reduced by using any one of the following methods:  

• Reducing the doping concentration of substrate material.  
• Increasing C_ox.   
• Reducing t_oxx² .  
• Using implantation techniques.   
• Replacing Al plate with polycrystalline silicon. 

1. Characteristics &  Operation of Depletion Type MOSFETs
2. Characteristics &  Operation of Enhancement Type MOSFETs
3. Characteristics, Operation & Construction of Power MOSFETs
4. Power MOSFET Construction and Working
5. Performance Parameters & Characteristics of MOSFETs